Ufakelo lweRoller yoMnqongo weMila
Ukuze kuqinisekiswe ukuzinza kwezinto ezigqithisiweyo, ii-roller ezi-4 ziyafuneka ukuxhasa izinto ezihanjiswayo, oko kukuthi, ubude bezinto ezihanjiswayo (L) bukhulu okanye bulingana namaxesha amathathu ombindi womgama wedrum yokuxuba (d );kwangaxeshanye, ububanzi obungaphakathi besakhelo kufuneka bube bukhulu kunobubanzi bezinto ezihanjiswayo (W), kwaye ushiye umda othile. (Ngokuqhelekileyo, ixabiso eliphantsi yi-50mm)
Iindlela eziqhelekileyo zokufakela iirola kunye nemiyalelo:
| Indlela yokufakela | Ziqhelanise nemeko | Amagqabantshintshi |
| Ufakelo lweshaft oluguquguqukayo | Ukuhanjiswa komthwalo olula | Ufakelo lwe-elastic shaft press-fit-fit lusetyenziswa ngokubanzi kwizihlandlo zokuhambisa umthwalo okhanyayo, kwaye ukufakela kunye nokugcinwa kwayo kulula kakhulu. |
| Ukufakwa kweflethi yokugaya | umthwalo ophakathi | Ukunyuswa kwe-Milled flat kuqinisekisa ukugcinwa okungcono kune-spring-loaded shafts kwaye zifanelekile kwizicelo zomthwalo ophakathi. |
| Ufakelo lwentambo yabasetyhini | Ukuhanjiswa komsebenzi onzima | Ukufakwa kwentambo yoMfazi kunokutshixa i-roller kunye nesakhelo sisonke, esinokubonelela ngomthamo omkhulu wokuthwala kwaye ngokuqhelekileyo sisetyenziselwa uxanduva olunzima okanye ukuhanjiswa kwesantya esiphezulu. |
| Umsonto obhinqileyo + ukufakwa kweflethi yokusila | Uzinzo oluphezulu lufuna ukuhanjiswa komsebenzi onzima | Kwiimfuno ezikhethekileyo zokuzinza, intambo ye-Female ingasetyenziselwa ukudibanisa kunye nokugaya kunye nokunyuka kweflethi ukubonelela amandla amakhulu okuthwala kunye nokuzinza okungapheliyo. |
Inkcazo yokukhutshwa kwerola:
| Indlela yokufakela | Uluhlu lokucoca (mm) | Amagqabantshintshi |
| Ukufakwa kweflethi yokugaya | 0.5~1.0 | 0100 series ngokuqhelekileyo 1.0mm, abanye badla 0.5mm |
| Ukufakwa kweflethi yokugaya | 0.5~1.0 | 0100 series ngokuqhelekileyo 1.0mm, abanye badla 0.5mm |
| Ufakelo lwentambo yabasetyhini | 0 | Ucoceko lofakelo ngu-0, ububanzi bangaphakathi besakhelo bulingana nobude obupheleleyo besilinda L=BF. |
| enye | Customized |
Ufakelo lwerola yokuhambisa egobileyo
Iimfuno ze-angle yokufakela
Ukuze kuqinisekiswe ukuhanjiswa okuhamba kakuhle, i-angle ethile yokuthambekela iyadingeka xa i-roller yokuguqula ifakwe.Ukuthatha i-3.6 ° i-taper roller eqhelekileyo njengomzekelo, i-angle yokuthambekela idla ngokuba yi-1.8 °,
njengoko kubonisiwe kuMfanekiso 1:
IiMfuno zeRadiyo zokujika
Ukuqinisekisa ukuba into egqithisiweyo ayikhuhli kwicala lomhambisi xa ujika, le parameters yoyilo ilandelayo kufuneka ithathelwe ingqalelo: BF+R≥50 +√(R+W)2+(L/2)2
njengoko kubonisiwe kuMfanekiso 2:
Isalathiso soyilo lokuguqula iradiyasi yangaphakathi (i-roller taper isekelwe kwi-3.6 °):
| Uhlobo lomxube | Irediyasi yangaphakathi (R) | Ubude berola |
| Iirola zechungechunge ezingenamandla | 800 | Ubude beRoller ngama-300, 400, 500 ~ 800 |
| 850 | Ubude beRoller ngama-250, 350, 450 ~ 750 | |
| Transmission intloko series ivili | 770 | Ubude beRoller ngama-300, 400, 500 ~ 800 |
| 820 | Ubude beRoller ngama-250, 450, 550 ~ 750 |
